Products

Our Energy Storage Solutions

Discover our range of innovative energy storage products designed to meet diverse needs and applications.

  • All
  • Energy Cabinet
  • Communication site
  • Outdoor site
Experimental investigation on thermal performance of a battery liquid cooling structure …

Section snippets Design and processing of hp-cp structure The HP-CP structure and its application in individual battery cooling are shown in Fig. 1. The structure is composed of one cold plate and two heat pipe-cooper plate structures. The heat pipe-cooper plate ...

Thermal Design and Numerical Investigation of Cold Plate for Active Water Cooling for High-Energy Density Lithium-Ion Battery …

16.2.1 Domain CreationIn the present study, the heat source is applied to a three-battery module which is kept on top of a cold plate, and the battery is to be connected in a series arrangement which is in constant charge current of 3C, 2C, and 1C rate. Figure 16.1 shows the detailed 3D model.

Structure Optimization of Battery Module With a Parallel Multi-Channel Liquid Cooling Plate …

Abstract. In order to keep the power battery work within an ideal temperature range for the electric vehicle, the liquid cooling plate with parallel multi-channels is designed, and a three-dimensional thermal model of battery module with the liquid cooling plate is established. Subsequently, the effects of the cooling plate …

Optimization of guide plates and orifice plates on thermal management of battery energy storage …

A combined duct with guide plate and orifice plate is proposed for battery system. • Optimize the structure of guide plate and the porosity of orifice plate. • After optimization, air supply uniformity coefficient is reduced to 6.29%. • After optimization, temperature

New Energy Vehicle Charging Pile Solution

I. Construction background Developing new energy vehicles is the only road China must take to become an advanced automobile maker from a big automobile maker, and promoting the construction of charging pile infrastructure is a solid guarantee to implement this ...

Underground solar energy storage via energy piles

Fig. 2 shows a schematic diagram of the energy pile-solar collector coupled system to be modeled in this study. It consists of a flat-plate solar collector, an energy pile with the surrounding soil, and the water-bearing pipes. The building upon the pile foundation is …

Optimized design of liquid-cooled plate structure for flying car power battery …

The structure of the battery module studied in this paper is shown in Fig. 1, which consists of individual cell liquid cooling plates and coolant.The parameters of a single cell are provided in Table 1.According to reference [26], the rated energy for a flying car hovering for 1000s is 163.82 kWh. ...

Fin structure and liquid cooling to enhance heat transfer of composite phase change materials in battery …

1 INTRODUCTION As a power battery, lithium-ion batteries (LIBs) have become the fastest-growing secondary battery with the continuous development of electric vehicles (EVs). LIBs have high energy density and long service life. 1 However, the lifespan, performance and safety of LIBs are primarily affected by operation temperature. 2 The …

(PDF) Energy Storage Charging Pile Management Based on …

In this paper, the battery energy storage technology is applied to the traditional EV (electric vehicle) charging piles to build a new EV charging pile with …

Research on fast-charging battery thermal management system based on refrigerant direct cooling …

battery cooling technologies, direct refrigerant cooling not only has higher cooling e˚ciency, but also can sig nicantly reduce the cost of the whole vehicle, which is an important development ...

Deep learning-assisted design for battery liquid cooling plate with bionic leaf structure …

Firstly, the heat generation model for the natural cooling of the battery is established, and the cooling performance of the bionic vane cooling plate and the traditional cooling plate is compared. Then, a 5-layer fully connected artificial neural network is established for predicting maximum and minimum battery temperatures and fluid pressure drops.

A novel strategy to optimize the liquid cooling plates for battery thermal management by precisely tailoring the internal structure …

Immersion cooling (IC) has been treated as the most potential alternative to replace traditional liquid cooling (LC) systems for battery thermal management because of its simple structure and high cooling efficiency. However, …

Design And Application Of A Smart Interactive Distribution Area …

This paper proposes a collaborative interactive control strategy for distributed photovoltaic, energy storage, and V2G charging piles in a single low-voltage distribution station …

Structure optimization design and performance analysis of liquid …

In this paper, we have undertaken a systematic and logical design approach for the structure of the liquid cooling plate used in power batteries. Initially, …

Research papers Structure optimization of air cooling battery thermal management system based on lithium-ion battery …

The spoiler is applied to air cooling BTMS to improve the cooling performance. • Two common BTMSs are selected to study the applicability of installing spoiler. • Parametric analysis of three important structural parameters is investigated. • ∆T max of two optimized BTMSs are respectively reduced by 48.61% and 80.68%.

Simulation of cooling plate effect on a battery module with …

Numerous energy storage systems have been evolved so far to store the energy harnessed from renewable resources. These include electrical, thermal, chemical, electrochemical, and mechanical energy ...

Research Papers Structure optimization design and performance …

In this paper, we have undertaken a systematic and logical design approach for the structure of the liquid cooling plate used in power batteries. Initially, …

Experimental investigation on thermal management of lithium-ion battery with roll bond liquid cooling plate …

A liquid cooling plate with flexible flow channel design is fabricated using roll bond process, its thermal performance is verified experimentally. • Using proposed liquid cooling plate, the temperature of battery module is …

Comparative analysis of cooling effect of battery module cooling plate structures …

Finally, based on the simulation results, beneficial suggestions for the cooling and cooling plate design and manufacture of energy storage container battery modules are proposed. Parameters of ...

Numerical Analysis of Cooling Plates with Different Structures for Electric Vehicle Battery Thermal Management Systems …

PDF | On Aug 1, 2020, Ming Li and others published Numerical Analysis of Cooling Plates with Different Structures for Electric Vehicle Battery Thermal Management Systems ...